Westermo GD-01 TCP Interface Manual Download Page 119

Page: 119 / 206

119

6196-2220

&S – Set DSR signal

Description:

This commands controls the Data Set Ready (DSR) signal.

Syntax:

AT&S

Command example

Possible responses

Note

AT&S0

DSR always on

AT&S1

DSR off in command
mode, DSR on in data
mode

O – Back to online mode

Description:

If a connection has been established and the ME is in command mode, this command
allows you to return to online data mode.

Syntax:

ATO

Command example

Possible responses

Note

ATO

Return from offline mode
to online mode

Q – Result code suppression

Description:

This command determines whether the mobile equipment sends result codes or not

Syntax:

ATQ

Command example

Possible responses

Note

ATQ0

DCE transmits result
codes

ATQ1

(none)

Result codes are
suppressed and not
transmitted

Summary of Contents for GD-01 TCP















































































































































































































Search results

Summary of Contents for GD-01 TCP

Reviews:

Related manuals for GD-01 TCP

Brands by name

Popular brands

Westermo GD-01 TCP, Interface Manual

Search results

Summary of Contents for GD-01 TCP

Reviews:

Related manuals for GD-01 TCP

Brands by name

Popular brands