Westermo GD-01 TCP Interface Manual Download Page 98

Page: 98 / 206

6196-2220

+CRLP – Radio link protocol parameters

Description:

This command allows the radio link protocol parameters used for non transparent data
transmission to be changed.

Syntax:

AT+CRLP=<iws>,<mws>,<T1>,<N2>, <ver>

Command example

Possible responses

Note

AT+CRLP=? +CRLP: (0-61),(0-61),

Test

command

(40-255),(1,255),(0,1)

AT+CRLP=61,61,48,6,0

Set new parameters

AT+CRLP? AT+CRLP: 61,61,48,6,0

Current

values

Defined values:

This command accepts 5 parameters.

<iws>

0-61: Down window size, (default is 61),

<mws>

0-61: Up window size, (default is 61),

<T1>

40-255: Acknowledgement timer in units of 10ms, (default is 48)

<N2>

1-255: Retransmission attempts, (default is 6),

<ver>

0-1:Version number. If V42bis is supported the version
is 1, If V42bis is not supported the version is 0

Summary of Contents for GD-01 TCP















































































































































































































Search results

Summary of Contents for GD-01 TCP

Reviews:

Related manuals for GD-01 TCP

Brands by name

Popular brands

Westermo GD-01 TCP, Interface Manual

Search results

Summary of Contents for GD-01 TCP

Reviews:

Related manuals for GD-01 TCP

Brands by name

Popular brands