Westermo GD-01 TCP Interface Manual Download Page 114

Page: 114 / 206

114

6196-2220

+FDCC – DCE capabilities parameters

Description:

This command allows the DTE to parameter the capabilities used for any session.

Syntax:

AT+FDCC=<vr>,<br>,<wd>,<ln>,<df>,<ec>,<bf>,<st>

Command example

Possible responses

Note

AT+ FDCC=?

(0,1),(0-5),(0-2),(0-2),(0-3),

Test command, Note:

(0),(0),(0-7)

Fax ECM not

supported. Fax 14,4 kbps
supported

Defined values:

The parameters and default values are the same as for the +FDIS command

+FLID – Local ID string

Description:

This command allows the local ID string to be defined.

Syntax:

AT+FLID=”<string>”

The string has a limited size, and accepts any characters between 32 and 127.

Command example

Possible responses

Note

AT+FLID=? (20),(32-127)

Test

command

+FPHCTO – Page transfer timeout parameter

Description:

This command sets the period the modem waits for another page before it assumes
there are no more pages and aborts.

Syntax:

AT+FPHCT0=<n> (default is 30)

Command example

Possible responses

Note

AT+FPHCTO=? (0-255)

Test

command

Summary of Contents for GD-01 TCP















































































































































































































Search results

Summary of Contents for GD-01 TCP

Reviews:

Related manuals for GD-01 TCP

Brands by name

Popular brands

Westermo GD-01 TCP, Interface Manual

Search results

Summary of Contents for GD-01 TCP

Reviews:

Related manuals for GD-01 TCP

Brands by name

Popular brands