manualshive.com logo in svg

Voith IPC 4, Operating Instructions Manual

Share
Download
Voith IPC 4 Operating Instructions Manual Download Page 46

46

Voith 

Turbo H + L

 Hydraulic GmbH & Co. KG

25000057510-TED-ENX-04

Note:

•  Apart from a few exceptions, it is not possible to operate pump combinations with 

different operating media because the suction areas of the respective pump  
stages are linked to each other. Designs with suction areas that are sealed off 
from each other are possible.

Please contact Voith Turbo H + L Hydraulic.

•  Pumps of the same or different sizes can be combined to form double pumps 

without restricting their maximum permitted pressures.

•  Triple or quadruple pumps are possible.
•  On the attachment pumps (secondary pumps) to the main pump, the drive shaft 

is always geared. The individual drive shafts are connected via geared couplings 
that are lubricated by the pressure fluid.

•  The individual pump stages are each fastened to the previous pump via the inter-

mediate housing.

Designs:

Intermediate housing with suction port:

Two pumps suck via one shared connection. The suction ports of the respective 
individual pumps are sealed with a blank cover.

Intermediate housing without suction port: 

The pumps each suck via the suction port of the respective individual pump. 

Internal gear pumps 

Pump combinations - configuration

www.Laheghi.com

Summary of Contents for IPC 4
























































Reviews:

No comments

Brands by name

Popular brands

Load more brands