manualshive.com logo in svg

Voith IPC 4, Operating Instructions Manual

Share
Download
Voith IPC 4 Operating Instructions Manual Download Page 36

36

Voith 

Turbo H + L

 Hydraulic GmbH & Co. KG

25000057510-TED-ENX-04

10.6  Commissioning of IPVPX pumps

Apart from the above commissioning of internal gear pumps, it is necessary to con-
sider further steps in the type IPVPX (Atex internal gear pumps with temperature 
sensor for control of ignition source). 

1. Mounting of the temperature sensor

The temperature sensor is packed separately and supplied with mounting screw, 
lock washer and thermal grease and must be mounted.

At mounting please note: the contact surface must be degreased and cleaned befo-
re wetting with the thermal compound. The fastening screw M4x16 must be tighte-
ned with a torque of 5 Nm.

The electrical connection must be made according to the specifications of the ope-
rating instructions of the sensor.

Fig.  10.6: Temperature sensor

DANGER

!

Overheating, incineration, explosion

In speed-controlled operation in load holding mode, the pump may over-
heat.

•  Don't operate the pump outside the permitted operating range.

www.Laheghi.com

Summary of Contents for IPC 4
























































Reviews:

No comments

Brands by name

Popular brands

Load more brands