manualshive.com logo in svg

Voith IPC 4, Operating Instructions Manual

Share
Download
Voith IPC 4 Operating Instructions Manual Download Page 26

26

Voith 

Turbo H + L

 Hydraulic GmbH & Co. KG

25000057510-TED-ENX-04

Falling loads can result in serious injury or death!

•  The internal gear pumps must only be hung at the designated suspending    
 points!
•   Only use suitable lifting gear that meets the safety requirements!
•   Never walk or move underneath swinging loads!
•   Tighten the steel ring screws into the flange thread as far as possible for  

 

 

transportation, otherwise the thread may break free!

DANGER

!

3.

  Only attach jack, crane, or cable hooks with spring clips to the ring screws for  

 

transporting the pump.

A swinging pump could cause serious injury or death from squashing.
Ensure hands and feet do not become trapped when pumps are lowered!

•  Weights of up to approx. 200 kg possible, depending on the design.
•   Note the new center of gravity.
•   Secure pump combinations against swinging/slipping/tipping.
•   Secure the pump/lifting gear with appropriate measures!
•   Wear safety gloves and safety shoes!

DANGER

!

4. 

Secure the pump to prevent it from swinging during transport.

5.

  Only raise the pump as high as necessary for transportation.

Transport the pump to the installation site..
Do not scratch the rating plate when setting down the pump; remove if necessary.

Internal gear pumps 

Packaging, transport

www.Laheghi.com

Summary of Contents for IPC 4
























































Reviews:

No comments

Brands by name

Popular brands

Load more brands