Veit SF26 Operating Instructions Manual Download

Page: 76 / 149

Remedy of faults/elimination of defects

CAUTION!

– Remedy of faults must only be carried out by

qualified personnel.

– In addition to the safety measures described

here, please carry out the safety measures

specified by the occupational insurance associ-

ation or by law.

– ATTENTION: There is a risk of burns caused

by hot machine parts.

Wear gloves and cover your arms, if required,

or wait until the machine has cooled down.

– Risk of electric shock.

CAUTION!

Repairs, troubleshooting and elimination of defects

must only be carried out by instructed and qualified

personnel.

Defect

Possible causes

Elimination of defects

Electrical defects

Damaged lines

Broken cable

Defective electrical compo-

nents

Qualified electrician

Mechanical defects

Damaged hose lines

Hoses not properly connected

Screw connections not prop-

erly installed, loose or leaking

Qualified person

9.1 Alarm messages on the touch screen

Listed according to their priority (lowest error

number = highest priority)

Remedy of faults/elimination of defects

Alarm messages on the touch screen

18.07.2017

Shirt finisher VEIT SF26

Summary of Contents for SF26






















































































































































Search results

Summary of Contents for SF26

Reviews:

Related manuals for SF26

Brands by name

Popular brands

Veit SF26, Operating Instructions Manual

Search results

Summary of Contents for SF26

Reviews:

Related manuals for SF26

Brands by name

Popular brands