manualshive.com logo in svg

Veit SF26, Operating Instructions Manual

Get your Veit SF26 operating instructions manual for free download at manualshive.com. This comprehensive manual covers every aspect of operating and maintaining your Veit SF26 product. With easy-to-follow instructions and detailed illustrations, this manual will ensure optimal performance and longevity of your machine.

Share
Download
background image

8.2.1  Battery replacement on touch panel PP65

Fig. 28: Battery replacement (EN)

To prevent data loss with regard to setup settings, date and time

settings, we recommend to replace the backup battery every three

years.

Tab. 16: Technical manufacturer specifications

Battery

Model

Renata 950 mAh

Type

Lithium-ions

Service life

n

Typical service life (with 50% backup operation: 25°C with device

switched off, 50°C with device switched on).

n

Maximum service life for 24 h operation (no backup): 6 years at

25°C, 5 years at 50°C.

n

Maximum service life with device switched off: 2 years at 25°C, 1

year at 50°C.

Can be

replaced

Yes, accessible from the outside

CAUTION!
Data loss

Risk of data loss. Machine setup data and machine

counter data are no longer saved. Please replace

battery immediately.

Warning "01 PLC battery, Attention data loss" indicates that there

only is little capacity of the PLC backup battery remaining. Replace

the battery immediately. Operation can be continued.

Manufacturer specifications

Maintenance and cleaning

Maintenance and inspection table > Battery replacement on touch panel PP65

18.07.2017

Shirt finisher VEIT SF26

73

Summary of Contents for SF26






















































































































































Reviews:

No comments

Related manuals for SF26

Brands by name

Popular brands

Load more brands