Veit SF26 Operating Instructions Manual Download Page 26

Page: 26 / 149

Potential dangers

The safety systems and safety instructions described in these

operating instructions must be observed.
The machine is operated from the front.
The operating area and the access area to the machine must be

kept free of tools and other objects. Make sure that the operating

area at and around the machine is clean and tidy.
Never place tools or other objects on the machine. Due to vibra-

tions, these objects may fall into the machine and cause severe

damage.

WARNING!
Risk of crushing!

Do not reach into the guiding mechanism of the

carriage and pressure clamps.

WARNING!

– There is always a risk of burns caused by hot

steam.

– Therefore: Proceed with caution when carrying

out steaming tests without garment.

– Keep your distance.

– Do not touch the steam and condensate lines.

– The machine must only be operated with the

bust properly mounted.

WARNING!

Protect the machine against frost.

Potential dangers

18.07.2017

Shirt finisher VEIT SF26

Summary of Contents for SF26






















































































































































Search results

Summary of Contents for SF26

Reviews:

Brands by name

Popular brands

Veit SF26, Operating Instructions Manual

Search results

Summary of Contents for SF26

Reviews:

Brands by name

Popular brands