Veit SF26 Operating Instructions Manual Download Page 49

Page: 49 / 149

Pressing the button opens the keypad with letters from Q

- Z.

Shift button

For selecting the special characters in Pos. 1

For selecting capitalisation in Pos. 2 and Pos. 3

7.3.1.3 Message line

Green = operating message

During normal operation, the current process or the action that

follows activation of the pedal is displayed.

In the service menu, the current page function is displayed.

Yellow = warning message
In the event of a warning, the warning number and warning text are

displayed.

Red = fault message
In the event of a fault or defect, the fault number and fault text are

displayed.

7.3.1.4 Menu bar

Stop button

Machine in automatic

mode

When pressing this button, the

machine is set from any operating

state to idle state.

Machine in idle state

Pressing the button starts the the run

to home position.

If the following is indi-

cated:
Warning
Fault
Defect

Pressing this button acknowledges

these messages.

Fig. 10: Operating message

Operation

Controls and indicators > Control panel

18.07.2017

Shirt finisher VEIT SF26

Summary of Contents for SF26






















































































































































Search results

Summary of Contents for SF26

Reviews:

Brands by name

Popular brands

Veit SF26, Operating Instructions Manual

Search results

Summary of Contents for SF26

Reviews:

Brands by name

Popular brands