Veit SF26 Operating Instructions Manual Download Page 20

Page: 20 / 149

Fig. 3: Built-in safety systems

Tab. 9: The machine is provided with the following safety devices:

Pos. Safety device

Interval Inspec-

tion

Main switch

It disconnects/connects the machine

from/to the power supply system

and is located on the left side of the

machine.

Switch cabinet cover

The switch cabinet cover prevents

that live parts can be accessed.
The switch cabinet cover may only

be opened by qualified electricians

or electrically instructed persons.

Emergency stop button

The machine has an emergency

stop button which is located on the

control panel.

Mains disconnecting device (con-

nector of the mains connection

cable)

Pneumatic main valve

The maintenance unit containing the

pneumatic main valve is located on

the machine back side.

Steam stop valve

Condensate stop valve

Warning signs

Safety

Built-in safety systems

18.07.2017

Shirt finisher VEIT SF26

Summary of Contents for SF26






















































































































































Search results

Summary of Contents for SF26

Reviews:

Brands by name

Popular brands

Veit SF26, Operating Instructions Manual

Search results

Summary of Contents for SF26

Reviews:

Brands by name

Popular brands