Veit SF26 Operating Instructions Manual Download

Page: 35 / 149

WARNING!
Work on electric supply lines must only be car-

ried out by a qualified electrician. Unplug the

mains disconnecting device prior to opening

the machine. Danger to life.

WARNING!
Mains disconnecting device

The mains disconnecting device of the machine is

the connector of the mains connection cable.
The connector must be freely accessible and must

not be blocked.
Unplug the mains disconnecting device (unplug the

connector) or press the emergency stop button to

switch off the machine in the event of danger.

CAUTION!
Protection against ESD

Before touching the printed circuit board, make

sure that the person is grounded (ESD protection

or by touching a heating element/water pipe).

Additional equipotential bonding must be connected to the device.

It must be connected to the M8 bolt on the rear side of the device.

NOTICE!
Residual current circuit breaker

If, on the mains side, an RCCB (residual current

circuit breaker) is located in the circuit to which the

device is connected, it must be "sensitive to uni-

versal current" (type B).

NOTICE!
Electrical connection ratings

For the electrical connection ratings, please refer

to .

Installation

Installation > Power supply connection

18.07.2017

Shirt finisher VEIT SF26

Summary of Contents for SF26






















































































































































Search results

Summary of Contents for SF26

Reviews:

Related manuals for SF26

Brands by name

Popular brands

Veit SF26, Operating Instructions Manual

Search results

Summary of Contents for SF26

Reviews:

Related manuals for SF26

Brands by name

Popular brands