Veit SF26 Page 40 Operating Instructions Manual Download

Page: 40 / 149

6.3.3 Condensate connection

The SF26 shirt finisher is connected to a condensate line using a

condensate drain.

The use of other condensate drains is not permitted and may

lead to malfunctions.

We therefore recommend using

The SF26 mounting kit without CTP (for machines without cuff

tuck press), order no. 130060 or

The SF26 mounting kit with CTP (for machines with cuff tuck

press), order no. 130061

Internal diameter of the con-

densate drain

1/2''

CAUTION!
Risk of burns, hot steam

During operation there is a risk of serious skin

burns.
– Do not touch the hot metal surfaces.

– Do not reach into the hot flow of steam or air.

– Do not touch the steam and condensate lines.

Installation

Installation > Condensate connection

18.07.2017

Shirt finisher VEIT SF26

Summary of Contents for SF26






















































































































































Search results

Summary of Contents for SF26

Reviews:

Related manuals for SF26

Brands by name

Popular brands

Veit SF26, Operating Instructions Manual

Search results

Summary of Contents for SF26

Reviews:

Related manuals for SF26

Brands by name

Popular brands