Veit SF26 Operating Instructions Manual Download

Page: 51 / 149

Cancel

Pressing the button cancels the action.

Previous step

The button is only displayed in automatic mode. Every step can be

reset as long as the steaming phase has not been started.

Switching between simplified/extended menu

In operating mode, this button is used to switch between the simpli-

fied menu and the extended menu (standard).

The simplified menu provides a reduced scope of

functions and is limited to the main control ele-

ments. However, the function of the individual con-

trol elements is identical to those of the extended

menu.

7.3.1.5 Operating mode

Fig. 11: Extended operating mode

Fig. 12: Simplified operating mode

Operation

Controls and indicators > Control panel

18.07.2017

Shirt finisher VEIT SF26

Summary of Contents for SF26






















































































































































Search results

Summary of Contents for SF26

Reviews:

Related manuals for SF26

Brands by name

Popular brands

Veit SF26, Operating Instructions Manual

Search results

Summary of Contents for SF26

Reviews:

Related manuals for SF26

Brands by name

Popular brands