VeEX MTX150x Lite User Manual Download Page 86

Page: 86 / 148

Platform Functions

Fiber Scope Capture - PASS

In the example above, the message in blue states that the image can be saved when tapped. This indicates
that the

Autosave

on Tap option was enabled on

Page 1

of the

Setup

tab. If

Autosave after freeze

were

selected, no message to tap the screen would appear.

Page 2

displays all numeric results from defect and scratch events found for all four zones. These are used for

the evaluation of the Pass/Fail criteria, according to the IEC 61300-3-35 standard. (Scratch requirements refer
to width.)

This table will also be included in the reports.

Pass/Fail IEC analysis table

(Measured scratches and defects compared with threshold criteria for each fiber layer)

Summary of Contents for MTX150x Lite














































































































































Search results

Summary of Contents for MTX150x Lite

Reviews:

Related manuals for MTX150x Lite

Brands by name

Popular brands

VeEX MTX150x Lite, User Manual

Search results

Summary of Contents for MTX150x Lite

Reviews:

Related manuals for MTX150x Lite

Brands by name

Popular brands