VeEX MTX150x Lite User Manual Download Page 24

Page: 24 / 148

Basic Operation

Signal:

A valid input signal is detected

Frame:

Valid framing on the input signal is detected

Pattern:

Indicates test pattern synchronization in BERT, RFC, and Throughput

modes

Alarm/Error:

Alarms or errors are detected

Dual Port LED Status Lights

Signal:

A valid input signal is detected

Frame:

Valid framing on the input signal is detected

Pattern:

Indicates test pattern synchronization in BERT, RFC, and Throughput

modes

Alarm/Error:

Alarms or errors are detected

Test Ports:

P1 (port 1) and P2 (port 2) can be used to switch views in dual port

mode

The color indicates the alarm status:

Green:

No error or alarm is present

Red:

An error or alarm condition is currently detected

Red flashing:

Event history reminder. Any error or alarm has occurred in the past, but no longer

present.

Yellow:

An error or alarm was detected during the measurement interval but is no longer present or

active

Grey:

Status not applicable or the test has not begun yet

For test modes that support dual ports, P1 and P2 indicates the port in operation.

Summary of Contents for MTX150x Lite














































































































































Search results

Summary of Contents for MTX150x Lite

Reviews:

Related manuals for MTX150x Lite

Brands by name

Popular brands

VeEX MTX150x Lite, User Manual

Search results

Summary of Contents for MTX150x Lite

Reviews:

Related manuals for MTX150x Lite

Brands by name

Popular brands