VeEX MTX150x Lite User Manual Download Page 31

Page: 31 / 148

Ethernet

10 GE Port

10GE Mode:

LAN or WAN

WIS Mode

(only available in WAN mode): SDH or SONET

Flow Control:

Enable chosen as default option

Clock Offset (ppm):

The frequency may be offset in parts per million

Link Fault Response:

Disable or Enable (also enables Local link and failure, remote, failure)

Transmit Ignore Link Status:

On/Off

Synchronous Ethernet

: (SyncE) Disabled or Enabled. When Enabled, makes the signal traceable

to an internal or external reference clock.

Measurement Settings

Measurement Setup

The measurement and event log settings are configured in this screen.

Mode:

Manual, timed, or auto mode are available.

Manual mode:

Starts and stops the measurements manually.

Timed mode:

Defines the duration of the test; after the test is started, the test will run for the

configured duration and stop automatically.

Summary of Contents for MTX150x Lite














































































































































Search results

Summary of Contents for MTX150x Lite

Reviews:

Related manuals for MTX150x Lite

Brands by name

Popular brands

VeEX MTX150x Lite, User Manual

Search results

Summary of Contents for MTX150x Lite

Reviews:

Related manuals for MTX150x Lite

Brands by name

Popular brands