Vacon 100 HVAC Applications Manual Download Page 33

Page: 33 / 201

The rotation direction changes immediately. You

can see that the arrow indication in the status field

of the display changes.

STOP

READY

I/O

ID:

Main Menu

Monitor

( 7 )

Parameters

( 15 )

Diagnostics

( 6 )

3.2.4

COPYING THE PARAMETERS

NOTE!

This function is available only in the graphical display.

Before you can copy parameters from the control panel to the drive, you must stop the drive.

COPYING THE PARAMETERS OF AN AC DRIVE

Use this function to copy parameters from a drive to another.

Save the parameters to the control panel.

Detach the control panel and connect it to another

drive.

Download the parameters to the new drive with the

command Restore from keypad.

SAVING THE PARAMETERS TO THE CONTROL PANEL

Go into the User settings menu.

STOP

READY

Keypad

ID:

Main Menu

I/O and Hardware

( 9 )

User settings

( 4 )

Favourites

( 0 )

USER INTERFACES

VACON · 33

24-HOUR S358 (0)201 212 575 · EMAIL: [email protected]

Summary of Contents for 100 HVAC










































































































































































































Search results

Summary of Contents for 100 HVAC

Reviews:

Related manuals for 100 HVAC

Brands by name

Popular brands

Vacon 100 HVAC, Applications Manual

Search results

Summary of Contents for 100 HVAC

Reviews:

Related manuals for 100 HVAC

Brands by name

Popular brands