Vacon 100 HVAC Applications Manual Download Page 196

Page: 196 / 201

Table 61: Fault codes

Fault

code

Fault ID Fault name

Possible cause

How to correct the fault

520

Safety diagnostics

The STO inputs have a dif-

ferent status.

Do a check of the external safety

switch. Do a check of the input

connection and cable of the safety

switch.

Reset the drive and restart.

If the fault occurs again, ask

instructions from your nearest dis-

tributor.

521

Safety diagnostics

A malfunction in the ATEX

thermistor diagnostic. There

is no connection in the ATEX

thermistor input.

Reset the drive and restart.

If the fault occurs again, change

the option board.

522

Safety diagnostics

A short-circuit in the con-

nection of the ATEX ther-

mistor input.

Do a check of the ATEX thermistor

input connection.

Do a check of the external ATEX

connection.

Do a check of the external ATEX

thermistor.

523

Safety diagnostics

A problem occured in the

internal safety circuit.

Reset the drive and restart.

If the fault occurs again, ask

instructions from your nearest dis-

tributor.

524

Safety diagnostics

An overvoltage in the safety

option board

Reset the drive and restart.

If the fault occurs again, ask

instructions from your nearest dis-

tributor.

525

Safety diagnostics

An undervoltage in the

safety option board

Reset the drive and restart.

If the fault occurs again, ask

instructions from your nearest dis-

tributor.

526

Safety diagnostics

An internal malfunction in

the safety option board CPU

or in the memory handling

Reset the drive and restart.

If the fault occurs again, ask

instructions from your nearest dis-

tributor.

527

Safety diagnostics

An internal malfunction in

the safety function

Reset the drive and restart.

If the fault occurs again, ask

instructions from your nearest dis-

tributor.

530

Safe torque off

An emergency stop was

connected or some other

STO operation was activa-

ted.

When the STO function is activated,

the drive is in safe state.

312

Fan cooling

The fan life time is com-

plete.

Replace the fan and reset the life

time counter of the fan.

VACON · 196

FAULT TRACING

TEL. +358 (0)201 2121 · FAX +358 (0)201 212 205

Summary of Contents for 100 HVAC










































































































































































































Search results

Summary of Contents for 100 HVAC

Reviews:

Related manuals for 100 HVAC

Brands by name

Popular brands

Vacon 100 HVAC, Applications Manual

Search results

Summary of Contents for 100 HVAC

Reviews:

Related manuals for 100 HVAC

Brands by name

Popular brands