Vacon 100 HVAC Applications Manual Download Page 118

Page: 118 / 201

Selection

number

Selection name

Description

Yes

The keypad stop button is always enabled.

Limited function of the keypad stop button.

P3.2.4 START FUNCTION (ID 505)

Use this parameter to select the type of the start function.

Selection

number

Selection name

Description

Ramping

The drive drive accelerates from 0 frequency to frequency

reference.

Flying start

The drive detetcts the actual speed of the motor and acceler-

ates from that speed to frequency reference.

P3.2.5 STOP FUNCTION (ID 506)

Use this parameter to select the type of the stop function.

Selection

number

Selection name

Description

Coasting

The motor stops on its inertia. When the stop command is

given, the control by the drive stops and the current from the

drive goes to 0.

Ramp

After the stop command, the speed of the motor is decreased

to zero speed according to the deceleration parameters.

NOTE!

Ramp stop cannot be guarenteed in all situations. If ramp stop is selected and the

net voltage changes over 20 %, the voltage estimation fails. In such case, ramp stop

is not possible.

P3.2.6 I/O START/STOP LOGIC (ID 300)

Use this parameter to control the start and stop of the drive with the digital signals.

The selections can include the word 'edge' to help you prevent an accidental start.

An accidental start can occur, for example, in these conditions

•

When you connect the power.

•

When the power is connected again after a power cut.

•

After you reset a fault.

•

After Run Enable stops the drive.

•

When you change the control place to I/O control.

VACON · 118

PARAMETER DESCRIPTIONS

TEL. +358 (0)201 2121 · FAX +358 (0)201 212 205

Summary of Contents for 100 HVAC










































































































































































































Search results

Summary of Contents for 100 HVAC

Reviews:

Related manuals for 100 HVAC

Brands by name

Popular brands

Vacon 100 HVAC, Applications Manual

Search results

Summary of Contents for 100 HVAC

Reviews:

Related manuals for 100 HVAC

Brands by name

Popular brands