Vacon 100 HVAC Applications Manual Download Page 194

Page: 194 / 201

Table 61: Fault codes

Fault

code

Fault ID Fault name

Possible cause

How to correct the fault

Undervoltage (fault)

The DC-link voltage is lower

than the limits.

•

too low a supply volt-

age

•

AC drive internal fault

•

a defective input fuse

•

the external charge

switch is not closed

NOTE!

This fault becomes active

only if the drive is in Run

state.

If there is a temporary supply volt-

age break, reset the fault and

restart the drive.

Do a check of the supply voltage. If

the supply voltage is sufficient,

there is an internal fault.

Ask instructions from the distribu-

tor near to you.

Undervoltage (alarm)

Input phase

The input line phase is

missing.

Do a check of the supply voltage,

the fuses and supply cable.

100

Output phase super-

vision

The measurement of cur-

rent tells that there is no

current in 1 motor phase.

Do a check of the motor cable and

the motor.

120

AC drive undertem-

perature (fault)

Too low a temperature in

the heatsink of the power

unit or in the power board.

The heatsink temperature is

less than -10 °C.

121

AC drive undertem-

perature (alarm)

130

AC drive overtemper-

ature (fault, heatsink)

Too high a temperature in

the heatsink of the power

unit or in the power board.

The heatsink temperature is

more than 100 °C.

Do a check of the actual quantity

and flow of cooling air.

Examine the heatsink for dust.

Do a check of the ambient temper-

ature.

Make sure that the switching fre-

quency is not too high in relation to

the ambient temperature and the

motor load.

131

AC drive overtemper-

ature (alarm, heat-

sink)

132

AC drive overtemper-

ature (fault, board)

133

AC drive overtemper-

ature (alarm, board)

140

Motor stalled

The motor stalled.

Do a check of the motor and the

load.

150

Motor overtempera-

ture

There is too heavy a load on

the motor.

Decrease the motor load. If there is

no motor overload, do a check of

the temperature model parame-

ters.

160

Motor underload

There is not a sufficient load

on the motor.

Do a check of the load.

VACON · 194

FAULT TRACING

TEL. +358 (0)201 2121 · FAX +358 (0)201 212 205

Summary of Contents for 100 HVAC










































































































































































































Search results

Summary of Contents for 100 HVAC

Reviews:

Related manuals for 100 HVAC

Brands by name

Popular brands

Vacon 100 HVAC, Applications Manual

Search results

Summary of Contents for 100 HVAC

Reviews:

Related manuals for 100 HVAC

Brands by name

Popular brands