Vacon 100 HVAC Applications Manual Download Page 182

Page: 182 / 201

An autochange is done when the autochange interval has elapsed, the number of running

motors is less than autochange motor limit and the controlling drive is running below

autochange frequency limit.

P3.14.8 BANDWIDTH (ID 1097)

Use this parameter to set the bandwith area around the PID setpoint for starting and

stopping of the auxiliary motors.

When the PID feedback value stays in the bandwith area, the auxiliary motors do not start or

stop. The value of this parameter is given as a percentage of the setpoint.

P3.14.9 BANDWIDTH DELAY (ID 1098)

Use this parameter to set the duration before the auxiliary motors start or stop.

When the PID feedback is not in the bandwidth area, the time that is set with this parameter

must go before the auxiliary motors start or stop. The number of pumps that operate

increases or decreases, if the PID controller cannot keep the process value (feedback) in the

specified bandwidth around the setpoint.

The bandwidth area is specified as a percentage of the PID setpoint. When the PID feedback

value stays in the bandwidth area, it is not necessary to increase or decrease the number of

pumps that operate.

When the feedback value goes out of the bandwidth area, the quantity of time specified by

parameter P3.14.8 must go before the number of pumps that operate increases or

decreases. More pumps must be available.

ID 1097

ID 1098

Fig. 50: The start or stop of the auxiliary pumps (P3.14.8 = Bandwidth, P3.14.9 = Bandwidth delay)
A. The pump that controls the system

operates at a frequency that is near the

maximum (-2Hz). This increases the

number of pumps that operate.

B. The pump that controls the system

operates at a frequency that is near the

minimum (+2Hz). This decreases the

number of pumps that operate.

VACON · 182

PARAMETER DESCRIPTIONS

TEL. +358 (0)201 2121 · FAX +358 (0)201 212 205

Summary of Contents for 100 HVAC










































































































































































































Search results

Summary of Contents for 100 HVAC

Reviews:

Related manuals for 100 HVAC

Brands by name

Popular brands

Vacon 100 HVAC, Applications Manual

Search results

Summary of Contents for 100 HVAC

Reviews:

Related manuals for 100 HVAC

Brands by name

Popular brands