Vacon 100 HVAC Applications Manual Download Page 131

Page: 131 / 201

P3.4.11 FREQUENCY TO START DC BRAKING AT RAMP STOP (ID 515)

Use this parameter to set the output frequency at which the DC braking starts.

P3.4.12 FLUX BRAKING (ID 520)

Use this parameter to enable the Flux Braking function.

You can use flux braking as an alternative to DC braking. Flux braking increases the braking

capacity in conditions where additional brake resistors are not necessary.

When braking is necessary, the system decreases the frequency and increases the flux in the

motor. This increases the capacity of the motor to brake. The motor speed is controlled

during braking.

You can enable and disable Flux Braking.

CAUTION!

Use the braking only intermittently. Flux braking converts energy into heat and can

cause damage to the motor.

P3.4.13 FLUX BRAKING CURRENT (ID 519)

Use this parameter to set the current level for the flux braking.

10.5

I/O CONFIGURATION

10.5.1

PROGRAMMING OF DIGITAL AND ANALOGUE INPUTS

The programming of inputs of the AC drive is flexible. You can freely use the available inputs

of the standard and optional I/O for different functions.

Use the formats below to give the value for the programmable parameters:

•

DigIN SlotA.1 / AnIN SlotA.1 (graphical keypad) or

•

dI A.1 / aI A.1 (text keypad).

Selection name

Example

Description

Input type

DigIN / dI

DigIN / dI = Digital input

AnIN / aI = Analogue input

Slot type

Slot A

The board type:

A / B = Vacon AC drive standard board

C / D / E = Option board

0 = The parameter signal is not connected to any terminal

Terminal number

The number of the terminal on the selected board.

PARAMETER DESCRIPTIONS

VACON · 131

24-HOUR S358 (0)201 212 575 · EMAIL: [email protected]

Summary of Contents for 100 HVAC










































































































































































































Search results

Summary of Contents for 100 HVAC

Reviews:

Related manuals for 100 HVAC

Brands by name

Popular brands

Vacon 100 HVAC, Applications Manual

Search results

Summary of Contents for 100 HVAC

Reviews:

Related manuals for 100 HVAC

Brands by name

Popular brands