Vacon 100 HVAC Applications Manual Download

Page: 193 / 201

Table 61: Fault codes

Fault

code

Fault ID Fault name

Possible cause

How to correct the fault

600

System fault

There is no communication

between the control board

and the power.

Reset the fault and restart the

drive.

If the fault occurs again, ask

instructions from the distributor

near to you.

602

Watchdog has reset the

CPU.

603

The voltage of auxiliary

power in the power unit is

too low.

604

Phase fault: Output phase

voltage does not agree to

the reference.

605

Fault in CPLD, but there is

no detailed information

about the fault.

606

The software of the control

unit is not compatible with

the software of the power

unit.

Download the latest software from

the Danfoss website. Update the

drive with it.

If the fault occurs again, ask

instructions from the distributor

near to you.

607

The software version cannot

be read. There is no soft-

ware in the power unit.

Update the power unit software.

If the fault occurs again, ask

instructions from the distributor

near to you.

608

A CPU overload. A part of

the software (for example

application) has caused an

overload situation.

Reset the fault and restart.

If the fault occurs again, ask

instructions from the distributor

near to you.

609

Access to the memory is

failed. For example, the

retain variables could not be

restored.

610

Necessary device properties

cannot be read.

647

System fault

Software error.

Download the latest software from

the Danfoss website. Update the

drive with it.

If the fault occurs again, ask

instructions from the distributor

near to you.

648

Invalid function block is

used in the application. The

system software is not com-

patible with the application.

649

A resource overload. A

parameter loading, restor-

ing or saving malfunction.

FAULT TRACING

VACON · 193

24-HOUR S358 (0)201 212 575 · EMAIL: [email protected]

Summary of Contents for 100 HVAC










































































































































































































Search results

Summary of Contents for 100 HVAC

Reviews:

Related manuals for 100 HVAC

Brands by name

Popular brands

Vacon 100 HVAC, Applications Manual

Search results

Summary of Contents for 100 HVAC

Reviews:

Related manuals for 100 HVAC

Brands by name

Popular brands