Trox Technik FKRS-EU Installation And Operating Manual Download Page 70

Page: 70 / 176

Fig. 54: Mortar-based installation into a lightweight partition wall, FK-EU / FK2-EU and FKRS-EU combined

FKRS-EU

FK-EU / FK2-EU up to W

≤

800

400 mm

2.1

Mortar

3.2

Lightweight partition wall with metal support struc-

ture or steel support structure, cladding on both

sides

6.5

Mineral wool (depending on wall construction)

7.10

Trim panels

according to installation details Fig. 51 to Fig. 53

with FK2-EU

Up to EI 90 S

Note:

Alternative installation orientations of side-by-side, under or on top of one another possible. Details are avail-

able upon request.

For installation details FK-EU and FK2-EU, see the installation and operating manual for these fire damper types.

Installation

Lightweight partition walls and compartment wall... > Mortar-based installation

Fire damper Type FKRS-EU

Summary of Contents for FKRS-EU

















































































































































































Search results

Summary of Contents for FKRS-EU

Reviews:

Related manuals for FKRS-EU

Brands by name

Popular brands

Trox Technik FKRS-EU, Installation And Operating Manual

Search results

Summary of Contents for FKRS-EU

Reviews:

Related manuals for FKRS-EU

Brands by name

Popular brands