manualshive.com logo in svg

Trox Technik FKRS-EU, Installation And Operating Manual

For the Trox Technik FKRS-EU product, make sure to refer to the Installation And Operating Manual for detailed instructions on setup and use. This manual can be downloaded for free from our website. Ensure a smooth experience with this high-quality product by following the guidelines provided in the manual. Download now at manualshive.com.

Share
Download
background image

5.11.9 

Mortar-based installation in conjunction with lightweight ceilings

Fig. 120: Mortar-based installation into solid ceiling slab in conjunction with lightweight ceiling (Cadolto system),

shown upright (also applicable for suspended arrangement)

1

FKRS-EU

2.1

Mortar

2.2

Reinforced concrete

4.3

Modular ceiling (Cadolto system), installation

according to manufacturer's instructions and gen-

eral appraisal certificate

4.4

Partial concrete ceiling with reinforcement

7.5

Steel support structure

7.17

Trimmers, steel support structure

7.19

Fire-resistant cladding

9.2

Extension piece or duct

Up to EI 120 S

Additional requirements: mortar-based installation into solid ceiling slabs in conjunction with lightweight

ceilings

Modular ceiling (Cadolto) 

Ä

  33

≥

 40 mm distance from fire damper to load-bearing structural elements

≥

 45 mm distance between two fire dampers

Structural and fire resistance properties of the ceiling construction, including the attachment to the concrete or

any required reinforcement, have to be evaluated and ensured by others.

Installation

Solid ceiling slabs  > Mortar-based installation in conjunction with ...

 

Fire damper Type FKRS-EU

139

Summary of Contents for FKRS-EU

















































































































































































Reviews:

No comments

Related manuals for FKRS-EU

Brands by name

Popular brands

Load more brands