manualshive.com logo in svg

Trox Technik FKRS-EU, Installation And Operating Manual

For the Trox Technik FKRS-EU product, make sure to refer to the Installation And Operating Manual for detailed instructions on setup and use. This manual can be downloaded for free from our website. Ensure a smooth experience with this high-quality product by following the guidelines provided in the manual. Download now at manualshive.com.

Share
Download
background image

Fig. 30: Mortar-based installation into a solid wall, combined, FKRS-EU and FK-EU / FK2-EU

1a

FKRS-EU

1b

FK-EU / FK2-EU up to W 

×

 H 

≤

 800 

×

 400 mm

2.1

Mortar

3.1

Solid wall

Up to EI 90 S

Note:

 Alternative installation orientations of side-by-side, under or on top of one another possible. Details are avail-

able upon request.

For installation details FK-EU and FK2-EU, see the installation and operating manual for these fire damper types.

Additional requirements: mortar-based installation into solid walls

Solid wall 

Ä

  32

Installation

Solid walls  > Mortar-based installation

 

Fire damper Type FKRS-EU

42

Summary of Contents for FKRS-EU

















































































































































































Reviews:

No comments

Related manuals for FKRS-EU

Helios BAK Series Installation And Operating Instructions Manual preview
BAK Series
Brand: Helios Pages: 10
Tamco AIR-IQ2 Installation Manuallines preview
AIR-IQ2
Brand: Tamco Pages: 8

Brands by name

Popular brands

Load more brands