Trox Technik FKRS-EU Installation And Operating Manual Download

Page: 140 / 176

5.11.10 Dry mortarless installation with installation block ER

Fig. 121: Dry mortarless installation with installation block ER in solid ceiling slab, upright and suspended

FKRS-EU

2.18

Installation block ER with cover plate

4.1

Solid ceiling slab

5.8

Wallplug with fire protection suitability certifi-

cate, alternatively push through installation

–

Up to EI 90 S

Additional requirements: dry mortarless installation with installation block ER in solid ceiling slabs



Solid wall



Installation block ER, see



≥ 75 mm distance between installation block and load-bearing structural elements



≥ 200 mm distance between two installation blocks

Create an appropriate opening with

D1, see

Position the fire damper with the installation block in the centre of the installation opening and push it in up to

the cover plate.

Fix the cover plate with four threaded rods (push through installation) or with at least four M6 screws. For solid

walls and solid ceiling slabs, suitable steel anchors with building inspectorate approval must be used.

Installation

Solid ceiling slabs > Dry mortarless installation with installation ...

Fire damper Type FKRS-EU

140

Summary of Contents for FKRS-EU

















































































































































































Search results

Summary of Contents for FKRS-EU

Reviews:

Related manuals for FKRS-EU

Brands by name

Popular brands

Trox Technik FKRS-EU, Installation And Operating Manual

Search results

Summary of Contents for FKRS-EU

Reviews:

Related manuals for FKRS-EU

Brands by name

Popular brands