Toshiba P9, Installation & Operation Manual

Page: 189 / 306

P9 ASD Installation and Operation Manual 179
Acc/Dec Pattern 1 – 4
Program

Special

Acc/Dec Special
Four Acceleration times and four Deceleration times may be set up and run
individually.
Accel/Decel Time 1 – 4 may be selected using this parameter
setting or switched via threshold frequencies, or by discrete input terminal.
This parameter is used to select one of the four configured accel/decel profiles
to be used.
Settings:
1 — Acc/Dec 1
2 — Acc/Dec 2
3 — Acc/Dec 3
4 — Acc/Dec 4
Each Accel/Decel selection is comprised of an Acceleration Time ,
Deceleration Time , and a Pattern selection. Selection 1, 2, and 3 have a
Switching Frequency setting. The Switching Frequency is used as a threshold
frequency that, once reached, the ASD switches to the next higher Acc/Dec
selection (i.e., 1 to 2, 2 to 3, or 3 to 4). Switching Frequency settings are also
used during deceleration. A switching frequency setting is not required for

Acc/Dec 4 .
Acc/Dec 1 is set up using parameters F009 (Acc Time), F010 (Dec Time), F502
(Pattern), and F505 (Switching Frequency).
Acc/Dec 2 is set up using parameters F500 (Acc Time), F501 (Dec Time), F503
(Pattern), and F513 (Switching Frequency).
Acc/Dec 3 is set up using parameters F510 (Acc Time), F511 (Dec Time), F512
(Pattern), and F517 (Switching Frequency).
Acc/Dec 4 is set up using parameters F514 (Acc Time), F515 (Dec Time), and
F516 (Pattern).
This parameter ( F504 ) is used to manually select Acc/Dec 1 – 4 .
To switch using the Terminal Board , assign the functions Acc/Dec Switching
1 and Acc/Dec Switching 2 to two discrete input terminals. Activation
combinations of the two terminals result in the Acc/Dec 1 – 4 selections as
shown in Table 5 .
Figure 37 shows the setup requirements and the resulting output frequency
response when using Switching Frequency settings to control the Acc/Dec
response of the ASD output.
While operating using S-Pattern 1 , the system performance may be further
enhanced by the adjustment of parameters F506 – F509 . These settings provide
for upper and lower Acc/Dec limit adjustments. These settings are used to
extend or shorten the upper or lower Acc/Dec curve.
Note: If operating from the Hand mode, press Esc from the Frequency
Command screen to access this parameter.
Direct Access Number — F504
Parameter Type — Selection List
Factory Default — 1
Changeable During Run — Yes
Figure 37. Using Acc/Dec Switching.
Accel/Decel Switching Frequency 1
Program

Special

Accel/Decel Special
This parameter sets the frequency at which the acceleration control is switched
from the
Accel 1 profile to the Accel 2 profile during a multiple-acceleration
profile configuration.
Direct Access Number — F505
Parameter Type — Numerical
Factory Default — 30.00
Changeable During Run — Yes
Minimum — 0.00
Maximum — Maximum Freq. ( F011 )
Units — Hz
Table 5
. Using combinations of discrete
terminal activations Accel/Decel profiles
1 – 4 may be selected.
Acc/Dec Switching Truth Table
A/D SW 1 A/D SW 2 Acc/Dec # Out
0 0 1
0 1 2
1 0 3
1 1 4
1 = Discrete terminal activation.
1 — Accel time 1 ( F009 setting)
2 — Accel time 2 ( F500 setting)
3 — Accel time 3 ( F510 setting)
4 — Accel time 4 ( F514 setting)
5 — Decel time 4 ( F515 setting)
6 — Decel time 3 ( F511 setting)
7 — Decel time 2 ( F501 setting)
8 — Decel time 1 ( F010 setting)
F504 F505