Toshiba B-SX4 Series Key Operations Manual Download

Page: 72 / 135

- 69 -

(21) Web printer function setting (WEB PRINTER)

• OFF: Web printer function is disabled.

• ON: Web printer function is enabled.

(22) Reset process when the nInit signal is ON (INPUT PRIME)

• OFF: The reset process is not performed.

• ON: The reset process is performed.

(23) Ribbon near end detection setting (RBN NEAR END)

• 70 m: A ribbon near end state is detected when the remaining ribbon

length is 70 m.

• 30 m: A ribbon near end state is detected when the remaining ribbon

length is 30 m.

• OFF: A ribbon near end state is not detected.

NOTE: There are some variations in detecting the ribbon near end

state. It is preferable to use this setting for reference

purposes.

(24) Expansion I/O operation mode setting (EX. I/O)

•

TYPE1:

Standard

mode

•

TYPE2:

In-line

mode

(25) Centronics operation mode setting (CENTRO.)

•

SPP:

Compatibility

mode

•

ECP:

ECP

mode

FEED

RESTART

FEED

RESTART

FEED

RESTART

FEED

RESTART

FEED

RESTART

Summary of Contents for B-SX4 Series








































































































































Search results

Summary of Contents for B-SX4 Series

Reviews:

Related manuals for B-SX4 Series

Brands by name

Popular brands

Toshiba B-SX4 Series, Key Operations Manual

Search results

Summary of Contents for B-SX4 Series

Reviews:

Related manuals for B-SX4 Series

Brands by name

Popular brands