manualshive.com logo in svg

Toshiba B-SX4 Series, Key Operations Manual

Share
Download
Toshiba B-SX4 Series Key Operations Manual Download Page 104

 

- 101 -

6.6.2 Display 

Contents 

(1)  Sensor adjustment value display 

[ H ] 2 0 ° C      [ A ] 2 2 ° C

 

 

 

 

 

[ S ] 2 5 ° C     

 

 

 
 
 

[ R E F L E C T ] 

3 . 8 V

 

 

 
 

[ T R A N S . ]   

2 . 3 V

 

 

 

[ P E ] R 0 . 2 V 

T 4 . 6 V

 

 

 
 

 

[ R I B B O N ]   

4 . 1 V

 

 

 

(2) Supplementary explanation 

 

•  During the sensor check, each sensor status is monitored and displayed every 200 msec.   

(When the sensor status is changed, the display also changes.) 

 

•  When the [FEED] and [RESTART] keys are entered at the same time, the system mode 

menu is displayed. 

Open-air temperature sensor status 
(0 °C to 86 °C) 

Thermal head temperature sensor status 
(0 °C to 86 °C) 

Heat sink sensor status 
(25 °C, 80 °C, 90 °C, 99 °C) 
*:  When the Part No. of the MAIN PC Board is 7FM00503x00, this value

is not displayed.   

Reflective sensor status without paper 
(0.0 V to 5.0 V) 

Transmissive sensor status without paper 
(0.0 V to 5.0 V) 

Reflective sensor status 
(0.0 V to 5.0 V) 

Transmissive sensor status 
(0.0 V to 5.0 V) 

Ribbon end sensor status 
(0.0 V to 5.0 V) 

Summary of Contents for B-SX4 Series








































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands