manualshive.com logo in svg

Toshiba B-SX4 Series, Key Operations Manual

Share
Download
Toshiba B-SX4 Series Key Operations Manual Download Page 41

 

- 38 -

 

 

 

 

 

z

System mode for users (Operable system mode menus are limited.) 

 

While holding the [FEED] and [RESTART] keys down, turn the power on. 

Maintenance counter/Various parameters printout,   
Printer self-test operation and results printout,   
Thermal head broken dots check 

Feed fine adjustment, Cut position fine adjustment (or strip 
position fine adjustment), Back feed fine adjustment,   
X-coordinate fine adjustment, Print density fine adjustment 
(Thermal transfer/Direct thermal print mode), Ribbon motor drive 
voltage fine adjustment, Transmissive sensor manual threshold 
fine adjustment, Reflective sensor manual threshold fine 
adjustment,

 

Power OFF 

[RESTART] 

[FEED] 

[RESTART] 

[FEED] 

[RESTART] 

[FEED] 

[RESTART] 

Parameter setting, 1-dot slant line printout, 3-dot slant line 
printout, Character printout, Bar code printout, Non-printing 
Automatic printout for the assembly process (Transmissive 
sensor/Reflective sensor), Factory pattern printout

 

<1>DIAG.

 

<3>ADJUST SET

 

<4>TEST PRINT

 

[FEED] 

[RESTART] 

<2>PARAMETER SETTING

Installed solenoid type setting, Ribbon saving system setting

 

<10>RFID  

[FEED] 

[FEED] 

[RESTART] 

RFID read test, RFID module type selection,   
RFID carrier sense setting, RFID tag type selection, Max. number of 
RFID issue retries, RFID error tag detection, Max. number of RFID read 
retries, RFID read retry time-out, Max. number of RFID write retries,   
RFID write retry time-out, RFID adjustment for retry, RFID wireless 
power level, AGC threshold setting, Channel setting 

Continued from the previous page. 

Summary of Contents for B-SX4 Series








































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands