Toshiba B-SX4 Series Page 123 Key Operations Manual Download

Page: 123 / 135

- 120 -

NOTE: Option Check Details

By installing the tool for option check, the following connectors on the board are checked:

the solenoid connector (CN11), the peeled-off paper sensor connector (CN20), rewinder

overflow sensor connector (CN4), the rotary cutter detection connector (CN18).

If the check results in a failure, then the failed item number is displayed on the LCD.

[Failed item numbers]

1: Solenoid connector (CN11)

2: Peeled-off paper sensor connector (CN20)

3: Rewinder overflow sensor connector (CN4)

4: Rotary cutter detection connector (CN18)

* When the check is performed, all connectors of the tool for the option check must be

connected. A connector which is also used for supplying the power is included. If all

connectors are not connected, the check is not properly performed. Several failed

item numbers may be displayed.

Summary of Contents for B-SX4 Series








































































































































Search results

Summary of Contents for B-SX4 Series

Reviews:

Related manuals for B-SX4 Series

Brands by name

Popular brands

Toshiba B-SX4 Series, Key Operations Manual

Search results

Summary of Contents for B-SX4 Series

Reviews:

Related manuals for B-SX4 Series

Brands by name

Popular brands