Toshiba B-SX4 Series Page 52 Key Operations Manual Download | Manualshive

Page: 52 / 135

background image

- 49 -

Maintenance Counter

Count Conditions

Head-up solenoid drive time

Counts when the ribbon saving operation is performed.
For B-SX4:
When the power is off, a drive time of 32 seconds or less is
rounded down and backed up.
For B-SX5:
When the power is off, a drive time of 27 seconds or less is
rounded down and backed up.

RS-232C hardware error
count

Counts when a parity error or a framing error occurs.
* When data of several bytes is transmitted continuously,

counting is performed per byte.

System error count

Counts when a system error of No. 22 listed in section 5.10
“LCD MESSAGES AND LED INDICATIONS” occurs.

Momentary power interruption
count

Counts when a momentary power interruption occurs.

Number of successful RFID
write

Counts when an RFID write has succeeded.

Number of failure in RFID
write

Counts when an RFID write has failed.

(2) Various parameters check contents

Item Contents

Remarks

[PC] FEED

Feed fine adjustment

-50.0 mm to +50.0 mm

(See NOTE.)

CUT

Cut position (or strip position) fine
adjustment

-50.0 mm to +50.0 mm

(See NOTE.)

BACK

Back feed fine adjustment

-9.9 mm to +9.9 mm

(See NOTE.)

TONE(T)

Print density fine adjustment
(Thermal transfer print mode)

-10 to +10 step

TONE(D)

Print density fine adjustment
(Direct thermal print mode)

-10 to +10 step

RBN(FW)

Ribbon motor drive voltage fine
adjustment (Rewind)

-15 to +6 step

RBN(BK)

Ribbon motor drive voltage fine
adjustment (Back tension)

-15 to +10 step

[KEY] FEED

Feed fine adjustment

-50.0 mm to +50.0 mm

CUT

Cut position (or strip position) fine
adjustment

-50.0 mm to +50.0 mm

BACK

Back feed fine adjustment

-9.5 mm to +9.5 mm

TONE(T)

Print density fine adjustment
(Thermal transfer print mode)

-10 to +10 step

TONE(D)

Print density fine adjustment
(Direct thermal print mode)

-10 to +10 step

RBN(FW)

Ribbon motor drive voltage fine
adjustment (Rewind)

-15 to +0 step

RBN(BK)

Ribbon motor drive voltage fine
adjustment (Back tension)

-15 to +0 step

X ADJ.

X-coordinate fine adjustment

-99.5 mm to +99.5 mm

THRESHOLD<R>

Reflective sensor manual
threshold fine adjustment

0.0 V to 4.0 V

THRESHOLD<T>

Transmissive sensor manual
threshold fine adjustment

0.0 V to 4.0 V

«
...
50
51
52
53
54
...
»

Summary of Contents for B-SX4 Series








































































































































Reviews:

No comments

Related manuals for B-SX4 Series

Brand: NCR Pages: 8

Webster's Spelling Corrector NC-10

Brand: Franklin Pages: 8

Brand: TSL Pages: 22

PowerScan Area Imager

Brand: Datalogic Pages: 44

Skylark WMU2000

Brand: Alien Pages: 28

Brand: Duali Pages: 12

Brand: American Dynamics Pages: 20

Brand: Code Pages: 16

Brand: Baltech Pages: 5

Brand: IDTECH Pages: 8

FlashLink STI-UCF100

Brand: SimpleTech Pages: 5

Brand: iHome Pages: 8

Brand: Freescale Semiconductor Pages: 46

Brand: U-Line Pages: 18

Brand: LS Pages: 39

Brand: Leuze electronic Pages: 119

Brand: i.safe MOBILE Pages: 116

CHIPDRIVE DESKTOP PRO

Brand: SCM Microsystems Pages: 27

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands