Toshiba B-SX4 Series Page 8 Key Operations Manual Download

Page: 8 / 135

- 5 -

5.5 THRESHOLD

SETTING

5.5.1

Outline of Threshold Setting

When a label is printed, the printer detects the gap between the labels using the transmissive

sensor, and corrects the print position automatically to obtain a constant print position.

However, when a preprinted label is used, some inks may prevent proper positioning correction.

In this case, determine the transmissive sensor threshold manually by key operation and store

the value in the non-volatile memory (EEPROM).

A constant print position can also be obtained when printing on a preprinted label since the print

position is always corrected using the threshold stored in the non-volatile memory (EEPROM) by

selecting “3: Transmissive Sensor (when using the preprinted label)” for the sensor type of the

Issue Command.

When a label is printed by detecting the black mark on the back of the label, the reflective rate

variation of a place other than the black mark may prevent the proper positioning correction. In

this case, determine the reflective sensor threshold manually by key operation and store the

value in the non-volatile memory (EEPROM).

A constant print position can also be obtained when printing on a tag since the print position is

always corrected using the threshold stored in the non-volatile memory (EEPROM) by selecting

“4: Reflective Sensor (when using a manual threshold value)” for the sensor type of the Issue

Command.

5.5.2

Threshold Setting Operation Example

O N L I N E

B - S X 4 T

V 1 . 0 A

B - S X 4 T

V 1 . 0 A

T R A N S M I S S I V E

B - S X 4 T

V 1 . 0 A

R E F L E C T I V E

B - S X 4 T

V 1 . 0 A

(2) Load the preprinted label.

(No particular positioning is required.)

(8) The reflective sensor designation is

displayed.

(7) Press the [FEED] key.

(6) The sensor selection to set the

threshold manually is displayed.

The transmissive sensor designation is

displayed.

(4) The printer is in a pause state.

(3) Press the [PAUSE] key.

(1) Idling

[PAUSE]

Power ON

(5) Hold down the [PAUSE] key for 3

seconds or more while the printer is

paused.

[PAUSE]

[FEED]

(9) Press the [FEED] key.

[FEED]

Summary of Contents for B-SX4 Series








































































































































Search results

Summary of Contents for B-SX4 Series

Reviews:

Related manuals for B-SX4 Series

Brands by name

Popular brands

Toshiba B-SX4 Series, Key Operations Manual

Search results

Summary of Contents for B-SX4 Series

Reviews:

Related manuals for B-SX4 Series

Brands by name

Popular brands