Toshiba B-SX4 Series Key Operations Manual Download

Page: 55 / 135

- 52 -

Item Contents

Remarks

AUTO HD CHK

Automatic broken dots check
setting

ON: Automatic broken dots check

is performed.

OFF: Automatic broken dots check

is not performed.

ACK/BUSY

Centronics ACK/BUSY timing
setting

TYPE 1: The ACK signal is sent to

match the rising edge of
ACK signal and the falling
edge of the BUSY signal.

TYPE 2: The ACK signal is sent to

match the falling edge of
ACK signal and the falling
edge of the BUSY signal.

WEB PRINTER

Web printer function setting

ON: Enabled
OFF: Disabled

INPUT PRIME

Reset process when the nInit
signal is ON

ON: Reset is performed.
OFF: Reset is not performed.

RIBBON NEAR END

Ribbon near end detection setting

30 m: Ribbon near end state is

detected when the remaining
ribbon length is
approximately 30 m.

70 m: Ribbon near end state is

detected when the remaining
ribbon length is
approximately 70 m.

OFF: Ribbon near end state is not

detected.

EX.I/O MODE

Expansion I/O operation mode

TYPE1: Standard mode
TYPE2: In-line

mode

CENTRO MODE

Centronics operation mode

SPP: Compatibility mode
ECP: ECP mode

PLUG & PLAY

Plug-and-play operation setting

ON: Plug-and-play operation is

enabled.

OFF: Plug-and-play operation is

disabled.

LBL/RBN END

Label end/ribbon end process
setting

TYPE1: When a label end or

ribbon end state is
detected, the printer stops
even if it is printing.

TYPE2: When a label end or

ribbon end state is
detected, the printer prints
the current label as far as
possible, then stops.

PRE PEEL OFF

Pre-peel-off process setting

ON: Pre-peel-off operation is

performed.

OFF: Pre-peel-off operation is not

performed.

BACK SPEED

Back feed speed setting

STD: 3 ips
LOW: 2

ips

MAXI CODE SPEC.

MaxiCode specification setting

TYPE1: Compatible with the

current version

TYPE2: Special specification

THERMAL HEAD

Print head type setting

B-SX4

B-SX5

V1: TPH104R2, V1: TPH128R4,
V2: TPH104R7, V2: TPH128R5,
or equivalent

or equivalent

Summary of Contents for B-SX4 Series








































































































































Search results

Summary of Contents for B-SX4 Series

Reviews:

Related manuals for B-SX4 Series

Brands by name

Popular brands

Toshiba B-SX4 Series, Key Operations Manual

Search results

Summary of Contents for B-SX4 Series

Reviews:

Related manuals for B-SX4 Series

Brands by name

Popular brands