Toshiba B-SX4 Series Key Operations Manual Download

Page: 96 / 135

- 93 -

(10) Initial parameter values when turning the power on

• Menu selection:

Test print condition parameter setting

• Issue count setting (ISSUE COUNT): 1

• Print speed (PRINT SPEED):

6”/sec for B-SX4, 5”/sec for B-SX5

• Sensor selection (SENSOR): Transmissive

sensor

• Print type (PRT TYPE):

Thermal transfer print mode

• Issue type (TYPE):

Batch issue

• Label size (LABEL LEN.):

76 mm

• Paper feed (PAPER):

Paper feed is performed.

(11) Supplementary

explanation

• When the [FEED] and [RESTART] keys are pressed at the same time, the display shows

the system mode menu.

• If the [RESTART] or [FEED] key is held down for 0.5 seconds or more when a parameter

is set or the menu is selected, the printer enters repeat mode, in which the key is entered

repeatedly.

• Each fine adjustment parameter is effective for test print. However, the X-coordinate

fine adjustment is excluded.

• When an error occurs during a test print, the error message is displayed and printing is

stopped. The error is cleared by pressing the [PAUSE] key and the display shows the

system mode menu. Printing is not automatically resumed after the error is cleared.

• A selected menu or changed parameter becomes effective by pressing the [PAUSE] key.

Such a parameter is retained until the power is turned off.

• The label size greater than the image buffer length cannot be designated. If it is

designated, the printer prints in the image buffer length then stops, or the printer stops

because of an error.

• The test print for the assembly process is performed under the following conditions.

The parameter setting and print density fine adjustment value are ignored.

•

Operations:

Feeds one label.

Prints 3-dot slant lines.

Prints bar codes

Prints

characters

• Issue count:

5 for each operation

• Print speed:

6”/sec for B-SX4, 5”/sec for B-SX5

•

Sensor

designation:

Reflective or transmissive sensor

• Print type:

Thermal transfer print mode

• Issue mode:

Batch issue

• Label size:

76 mm

• Print density fine adjustment value: ±0

• When the transmissive sensor is selected, the gap between labels should be 3 mm.

Summary of Contents for B-SX4 Series








































































































































Search results

Summary of Contents for B-SX4 Series

Reviews:

Related manuals for B-SX4 Series

Brands by name

Popular brands

Toshiba B-SX4 Series, Key Operations Manual

Search results

Summary of Contents for B-SX4 Series

Reviews:

Related manuals for B-SX4 Series

Brands by name

Popular brands