manualshive.com logo in svg

Toshiba B-SX4 Series, Key Operations Manual

Share
Download
Toshiba B-SX4 Series Key Operations Manual Download Page 94

 

- 91 -

6.5.2 Setting 

Contents 

(1)  Test print mode selection 

 

• PRINT CONDITION 

(Test print condition parameter setting) 

 

• SLANT LINE (1DOT) 

(1-dot slant line printout) 

 

• SLANT LINE (3DOT) 

(3-dot slant line printout) 

 • 

CHARACTERS 

(Character 

printout) 

 

• BARCODE 

(Bar code printout) 

 • 

NON-PRINTING 

(Nothing 

prints) 

 

• FACTORY TEST 

(Line printout for assembly process) 

 

• AUTO PRINT (TRAN) 

(Assembly process automatic 

printout/transmissive sensor) 

 

• AUTO PRINT (REFL) 

(Assembly process automatic 

printout/reflective sensor) 

 

(2)  Test print condition parameter setting (PRINT CONDITION) 

 

• ISSUE COUNT 

(Issue count setting) 

 

• PRINT SPEED 

(Print speed) 

 • 

SENSOR 

(Sensor 

selection) 

 

• PRT TYPE 

(Print type) 

 • 

TYPE (Issue 

type) 

 

• LABEL LEN. 

(Label size) 

 

• PAPER FEED 

(Paper feed mode) 

 

• <4> TEST PRINT 

(Test print mode) 

 

• PRINT CONDITION 

(Print condition parameter setting) 

 

(3)  Issue count setting (ISSUE COUNT) 

 • 

5000 

(Issue 

count: 

5000) 

 • 

1000 

(Issue 

count: 

1000) 

 • 

500 

(Issue 

count: 

500) 

 • 

100 

(Issue 

count: 

100) 

 • 

50 

(Issue 

count: 

50) 

 • 

10 

(Issue 

count: 

10) 

 • 

5 

(Issue 

count: 

5) 

 • 

3 

(Issue 

count: 

3) 

 • 

1 

(Issue 

count: 

1) 

 

(4)  Print speed (PRINT SPEED) 

 B-SX4 

 

B-SX5 

 • 

10”/sec 

(10 

inches/sec) 

• 8”/sec  (8 inches/sec) 

 • 

6”/sec 

(6 

inches/sec) 

 • 

5”/sec 

(5 

inches/sec) 

 • 

3”/sec 

(3 

inches/sec) 

 • 

3”/sec 

(3 

inches/sec) 

 

FEED 

RESTART 

PAUSE 

FEED 

RESTART 

FEED 

RESTART 

Summary of Contents for B-SX4 Series








































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands