manualshive.com logo in svg

Toshiba B-SX4 Series, Key Operations Manual

Share
Download
Toshiba B-SX4 Series Key Operations Manual Download Page 128

 

- 125 -

(3)  RFID module type selection 

 

 

 

 

 

 

 

 

NONE:  No RFID kit is installed.   

 

U1: 

The RFID kit for UHF band (B-9704-RFID-U1-US/EU) is installed.   

 

H1: 

The RFID kit for HF band (B-9704-RFID-H1-QM) is installed.   

 

H2: 

The RFID kit for HF band (B-SX704-RFID-H2) is installed. 

 

U2: 

The RFID kit for UHF band (B-SX704-RFID-U2) is installed.   

 

This setting will become effective after the printer power is turned off, and back to on.   

 

(4)  RFID tag type selection 

 

c

 When the RFID module type is set to “NONE”: 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

d

 When the RFID module type is set to “U2”: 

 

 

 

 

 

 

 

e

 When the RFID module type is set to “H2”: 

 

 

 

 

 

FEED 

RESTART 

• U1: 

B-9704-RFID-U1-US/EU is installed. 

• H1: 

B-9704-RFID-H1-QM is installed. 

• NONE:  No RFID kit is installed.   

• U2: 

B-SX704-RFID-US is installed. 

• H2: 

B-SX704-RFID-H2 is installed. 

FEED 

RESTART 

• C220: 

13 

• Tag-it: 

12 

• I-Code: 

11   

• ISO18000-6B: 

23 

• EPC C1: 

22 

• EPC C0: 

21 

 

• NONE (When a tag type is not selected.) 

 

• C320: 

17 

• EPC C1 Gen2: 

24 

• C240: 

16 

• C210: 

15 

• ISO15693: 

14 

FEED 

RESTART 

• NONE (When a tag type is not selected.)   

• EPC C1 Gen2: 

24 

FEED 

RESTART 

• NONE (When a tag type is not selected.)   

• ISO15693: 

14 

Summary of Contents for B-SX4 Series








































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands