Toshiba B-SX4 Series Key Operations Manual Download

Page: 17 / 135

- 14 -

(7)

RS-232C transmission control method selection (XON+READY)

• XON/XOFF protocol

(An XON is not output when the power is

on and an XOFF is not output when the

power is off)

• READY/BUSY (DTR) protocol

(An XON is not output when the power is

on and an XOFF is not output when the

power is off)

• XON/XOFF + READY/BUSY (DTR) protocol (An XON is output when the power is on

and an XOFF is output when the power is

off)

• XON/XOFF protocol

(An XON is output when the power is on

and an XOFF is output when the power is

off)

• RTS protocol

(An XON is not output when the power is

on and an XOFF is not output when the

power is off)

(8)

Language selection for LCD messages (LCD)

•

ENGLISH

•

GERMAN

•

FRENCH

•

DUTCH

•

SPANISH

•

JAPANESE

•

ITALIAN

NOTE: When Japanese is selected, one part of the character codes is different. For

details, refer to the External Equipment Interface Specification (TAA-1380).

(9)

Setting for forward feed standby (FORWARD WAIT)

• ON (with automatic feed standby)

• POSITION (Fine adjustment value setting for the stop position after a forward feed)

• OFF (without automatic feed standby)

NOTE: When it is set to ON, if the printer is in the idle state for 1 second or more after a

label is issued, the printer automatically performs an approximately 13.7-mm

forward feed, then stops.

(10) Setting for the forward feed standby action (FW/BK ACT.)

• MODE 1 (Stops after 13.7-mm forward feed.)
• MODE 2 (Stops after 6-mm back feed and 3-mm forward feed.

(Only when the cut mode, thermal transfer, and feed gap sensor are
selected.) In other cases, the printer stops after 13.7-mm forward feed.)

(11) Setting for head-up operation in cut issue mode, or for using the rewinder in batch issue

mode (HU CUT/RWD.)

• ON (The head is lifted, or the rewinder is used.)

• OFF (The head is not lifted, or the rewinder is not used.)

(12) Installed solenoid type setting

•

TYPE

• TYPE 2 (Stronger pull force type)

Summary of Contents for B-SX4 Series








































































































































Search results

Summary of Contents for B-SX4 Series

Reviews:

Related manuals for B-SX4 Series

Brands by name

Popular brands

Toshiba B-SX4 Series, Key Operations Manual

Search results

Summary of Contents for B-SX4 Series

Reviews:

Related manuals for B-SX4 Series

Brands by name

Popular brands