Toshiba B-SX4 Series Page 71 Key Operations Manual Download

Page: 71 / 135

- 68 -

(15) Peel-off wait status selection (PEEL OFF STS)

• OFF: No peel-off wait status selection

• ON: Peel-off wait status selection

(16) [FEED] key function setting (FEED KEY)

• FEED:

One label is fed.

• PRINT: Data in the image buffer is printed on one label.

(17) Kanji code selection (KANJI CODE)

(18) Euro code setting

(19) Automatic head broken dots check setting (AUTO HD CHK)

• OFF: Head broken dots check is not automatically performed.

• ON: Head broken dots check is automatically performed.

(20) Centronics ACK/BUSY timing setting (ACK/BUSY)

•

TYPE

•

TYPE

FEED

RESTART

TYPE 1: For WINDOWS codes

TYPE 2: For original codes

FEED

RESTART

FEED

RESTART

FEED

RESTART

20H

FFH

KANJI CODE TYPE1

KANJI CODE TYPE2

[FEED]

[RESTART]

EURO CODE B0

EURO CODE B1

[FEED]

[RESTART]

Summary of Contents for B-SX4 Series








































































































































Search results

Summary of Contents for B-SX4 Series

Reviews:

Related manuals for B-SX4 Series

Brands by name

Popular brands

Toshiba B-SX4 Series, Key Operations Manual

Search results

Summary of Contents for B-SX4 Series

Reviews:

Related manuals for B-SX4 Series

Brands by name

Popular brands