Assembling the Handle Assembly (continued)
2. If removed, install the lower handle assembly (1) onto the frame assembly (5)
and secure with the 2 bolts (2), anti-rotation washer (3),and washer (4).
3. Lift the lower handle assembly until it contacts the stop, and torque the 2
bolts (Item 2 in
) to
95 to 101 N·m (70 to 75 ft-lb)
.
4. Install the handle mount (item 7 in
) to the upper receiver weldment
(10) and secure with 2 bolts (11) and 2 nuts (9).
5. Position the clutch bail link (5) in the handle mount (7). Install the spacer tube
(13) and 2 flange bushings (3) to the handle mount. Secure the clutch bail
link to the handle mount with the bolt (2) and flange nut (8).
6. Position the compression spring (6), spacer tube (13) and 2 bushings (3) into
the handle mount (7). Install the clutch bail assembly (4) to the handle mount
(7) and secure with the bolt (2) and flange nut (8).
7. If removed, install the left and right bail brackets (1 and 19) to the handle (20)
with the 2 torques-head screws (18).
8. Install the clutch bail assembly (item 4
) to the handle (16). Secure
the handle to the handle mount (7) with the 2 bolts (17) and 2 nuts (8).
9. Position the spring spacer (Item 24 in
) and handle torsion spring
(23) into the handle adjuster assembly (22). Install the handle adjuster
assembly to the upper receiver weldment (8) with the clevis pin (14), bearing
washer (15) and cotter pin (18).
10. If removed, install the lift assist handle (27) to the upper receiver weldment
(8) and secure with the bolts (11 and 16).
11. Slide the upper receiver weldment (item 8 in
) into the lower handle
assembly (19) and secure with the bolt (29) and flange nut (9).
Note:
Do not tighten bolt and nut. Install the nut to engage locking feature.
The upper receiver weldment (8) must be free to slide.
12. Reposition the wire harness.
13. If removed, install the flange bushings (5), bolt (12) and flange nut (13) into
the brake lever (6).
14. Position the brake lever (item 6 in
) to the upper receiver weldment
(8) and secure with the shoulder screw (4) and flange nut (7).
15. Install the InfoCenter mount (item 4 in
) onto the handle and secure
with the 4 screws (1).
16. Install the wire harness.
17. If removed, install the flange bushings (item 31 in
) inside the
throttle arm (1).
18. If removed, slide the throttle lever (34) onto the throttle arm (1) and secure
with bolt (32).
19. Torque tighten the bolt from
2.2 to 3.4 N·m (20 to 30 in-lb)
.
20. Install the throttle arm (1) to the handle assembly (3) and secure with bolt
(30), washer (2) and flange nut (20).
21. Install the bolt (item 21 in
) and 2 flange nuts (7) to the upper
receiver weldment (8). Ensure that the head of the bolt is resting the on
throttle arm (1).
22. Install the brake latch shaft; refer to
Assembling the Brake Latch Shaft (page
.
Greensmaster
®
eFlex 1021
Page 6–19
Controls, Wheels, and Accessories : Service and Repairs
20248SL Rev C
Summary of Contents for 04861
