Disassembling the Cutting Unit Drive Lever Assembly (continued)
2. Disconnect the battery pack; refer to
Disconnecting and Connecting the
Lithium Battery Pack (page 5–3)
.
3. Remove the bolts and washers (item 9 in
) that secures the control
covers (item 8 and 10) to the upper receiver weldment (25) and handle
assembly.
4. Remove the reel lever handle rod (2) from the reel lever assembly (27).
5. If necessary, remove the reel lever knob (3) from the reel lever handle (2).
6. Remove the cotter pin (18) and clevis pin (20) that secures the link assembly
(14) to the main control shaft (15).
7. Remove the cotter pin (18) and clevis pin (20) that secures the clevis
connector (19) to the reel lever assembly (27).
8. Remove the extension spring (21) from the reel lock lever (23).
9. Remove the flange nut (26) and shoulder screw (22) that secures the reel
lock lever (23) to the upper receiver weldment (25). Remove the reel lock
lever (23) and bail latch spacer (24).
10. Remove the retaining ring (4) and V-ring seal (1) that secures the reel lever
assembly (27) to the main control shaft (15). Slide and remove the reel
lever assembly.
11. Remove the socket head screws (6) and control shaft clamps (5) that secures
the main control shaft (15) to the upper receiver weldment (23).
12. Remove the main control shaft (15). If necessary, remove the split bushing
(16 and 12) from the main control shaft.
Assembling the Cutting Unit Drive Lever Assembly
1. If removed, apply a coat of grease in inner diameter of split bushings (item
16 and 12 in
) and install the split bushing (16 and 12) onto the
main control shaft (15).
2. Position the main control shaft (15) on the upper receiver weldment (25)
and secure the main control shaft (15) with control shaft clamps (5) and
the bolts (6).
3. Slide the reel lever assembly (27) and V-ring seal (1) onto the main control
shaft (15) and secure reel lever assembly with the retaining ring (4).
4. Install the reel lock lever (23) and bail latch spacer (24) to the upper receiver
weldment (25) and secure with the shoulder screw (22) and flange nut (26).
5. Install the link assembly (14) to the main control shaft (15) with clevis pin
(20). Secure the clevis pin with the cotter pin clip (13).
6. Install the clevis connector (19) to the reel lever assembly (27) with clevis pin
(20) and secure the clevis pin with the cotter pin clip (18).
7. Install the reel lever handle rod (2) to the reel lever assembly (27).
8. If removed, install the reel lever knob (3) to reel lever handle rod (2).
9. Install the control covers (8 and 10) to the handle assembly with bolts and
washers (9).
10. Connect the battery pack; refer to
Disconnecting and Connecting the Lithium
Battery Pack (page 5–3)
.
Greensmaster
®
eFlex 1021
Page 6–11
Controls, Wheels, and Accessories : Service and Repairs
20248SL Rev C
Summary of Contents for 04861
