Thermo Scientific Ion Torrent A45727 User Manual Download Page 21

Page: 21 / 163

Genexus

™

Integrated Sequencer input and output connections

The connection panel, power port, and an on/off switch are located on the right side of

the rear panel of the instrument.

Power port—100–240VAC port that provides power to the instrument.

On/off switch—Power switch, where the states are on ( | ) or off ( O ).

USB ports—Connects a USB device to the instrument.

Ethernet port—An RJ45 port that provides Ethernet (Gigabit) communication between the
sequencer and a local area network.

Ethernet port—An RJ45 port that provides Ethernet (Gigabit) communication between the
sequencer and an accessory instrument.

Chapter 1

Product information

Genexus

™

Integrated Sequencer input and output connections

Genexus

™

Integrated Sequencer User Guide

Summary of Contents for Ion Torrent A45727




































































































































































Search results

Summary of Contents for Ion Torrent A45727

Reviews:

Related manuals for Ion Torrent A45727

Brands by name

Popular brands

Thermo Scientific Ion Torrent A45727, User Manual

Search results

Summary of Contents for Ion Torrent A45727

Reviews:

Related manuals for Ion Torrent A45727

Brands by name

Popular brands