Thermo Scientific Ion Torrent A45727 User Manual Download Page 17

Page: 17 / 163

Contents

Carrier

color

Pool

Carriers/kit

Part No.

Storage

Oncomine

™

TCR Beta

‑

LR Assay GX (Cat. No. A46297)

Oncomine

™

TCR Beta

‑

LR Assay GX (panel

only)

Purple

RNA Pool 1

A40282

−30°C to

−10°C

Genexus

™

Strip 1

Red

—

A40254

2°C to 8°C

Genexus

™

Strip 2

‑

Blue

—

A40253

−30°C to

−10°C

Note:

Assays using Ion AmpliSeq

™

chemistry have primer pools that are loaded in

capped tubes in position 1 of the primer pool tube carriers. Empty uncapped tubes

are loaded in position 2.

Assays using Ion AmpliSeq

™

HD chemistry have FWD and REV primer pools that

are loaded in capped tubes in both positions of the primer pool tube carrier.

Required materials not supplied

Unless otherwise indicated, all materials are available through thermofisher.com.

MLS: Fisher Scientific (fisherscientific.com) or other major laboratory supplier.

Item

Source

MicroAmp

™

EnduraPlate

™

Optical 96-Well Clear Reaction

Plates with Barcode

4483352, 4483354

Adhesive PCR Plate Foils

AB0626

‑

, 200

‑

, and 1,000

‑

µL pipettes and appropriate filtered tips

MLS

Microcentrifuge tubes, 1.5-mL or 1.7-mL (low retention for

nucleic acids)

MLS

Vortex mixer with a rubber platform

MLS

Gloves, powder-free nitrile

MLS

Ice buckets and ice

—

Nuclease-free water, molecular biology grade

MLS

Isopropyl alcohol, 70% solution

MLS

Wipes, disposable lint-free

MLS

(Optional) Uninterruptible Power Supply (UPS)

[1]

MLS

[1]

For laboratories that experience frequent power outages or line voltage fluctuations, we recommend that you

use an uninterruptible power supply that is compatible with 2500 W output or higher.

Chapter 1

Product information

Required materials not supplied

Genexus

™

Integrated Sequencer User Guide

Summary of Contents for Ion Torrent A45727




































































































































































Search results

Summary of Contents for Ion Torrent A45727

Reviews:

Related manuals for Ion Torrent A45727

Brands by name

Popular brands

Thermo Scientific Ion Torrent A45727, User Manual

Search results

Summary of Contents for Ion Torrent A45727

Reviews:

Related manuals for Ion Torrent A45727

Brands by name

Popular brands