Thermo Scientific Ion Torrent A45727 User Manual Download Page 18

Page: 18 / 163

Recommended materials for nucleic acid isolation and quantification

Unless otherwise indicated, all materials are available through thermofisher.com.

MLS: Fisher Scientific (fisherscientific.com) or other major laboratory supplier.

Item

Source

Nucleic acid isolation

Ion AmpliSeq

™

Direct FFPE DNA Kit

A31133, A31136

RecoverAll

™

Total Nucleic Acid Isolation Kit for FFPE

AM1975

RecoverAll

™

Multi-Sample RNA/DNA Workflow

A26069

MagMAX

™

FFPE Total Nucleic Acid Isolation Kit

4463365

MagMAX

™

FFPE DNA/RNA Ultra Kit

A31881

PureLink

™

Genomic DNA Mini Kit

K1820-00

MagMAX

™

Cell

‑

Free DNA Isolation Kit

A29319

MagMAX

™

Cell-Free Total Nucleic Acid Isolation Kit

A36716

RNase

Zap

™

RNase Decontamination Solution

AM9780, AM9782, AM9784

Nucleic acid quantification

TaqMan

™

RNase P Detection Reagents Kit

(Recommended

for DNA only)

4316831

Qubit

™

4 Fluorometer

[1]

Q33226

One or more of the following kits for use with the Qubit

™

Fluorometer:

• Qubit

™

dsDNA HS Assay Kit (High-sensitivity DNA)

• Qubit

™

dsDNA BR Assay Kit (Broad range DNA)

• Qubit

™

RNA HS Assay Kit (High-sensitivity RNA)

• Qubit

™

RNA BR Assay Kit (Broad range RNA )

Q32851, Q32854, Q32850,

Q32853

Q32852, Q32855, Q10210,

Q10211

Library quantification (Library Runs only)

Ion Library TaqMan

™

Quantitation Kit

4468802

[1]

Qubit

™

2.0 Fluorometer and later are supported.

Chapter 1

Product information

Recommended materials for nucleic acid isolation and quantification

Genexus

™

Integrated Sequencer User Guide

Summary of Contents for Ion Torrent A45727




































































































































































Search results

Summary of Contents for Ion Torrent A45727

Reviews:

Related manuals for Ion Torrent A45727

Brands by name

Popular brands

Thermo Scientific Ion Torrent A45727, User Manual

Search results

Summary of Contents for Ion Torrent A45727

Reviews:

Related manuals for Ion Torrent A45727

Brands by name

Popular brands