Thermo Scientific Ion Torrent A45727 User Manual Download Page 134

Page: 134 / 163

Supplemental information

■

Maintain the sequencer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 134

■

Quantify FFPE DNA with the Qubit

™

Fluorometer . . . . . . . . . . . . . . . . . . . . . . 135

■

Guidelines for using custom assays with the Genexus

™

Integrated Sequencer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 136

■

Planning sequencing runs for efficient use of consumables . . . . . . . . . . . . . . . . 138

■

Configure an Ion Reporter

™

Server account (administrator) . . . . . . . . . . . . . . . 139

■

Configure Thermo Fisher (Connect) accounts (manager/administrator) . . . . . 141

Maintain the sequencer

Cleaning

• Lint-free wipes
• 70% isopropanol
• (Optional) 10% bleach solution

Filter replacement

• Genexus

™

Filter (from the Genexus

™

Installation and Training Kit)

If a spill or leak occurs inside the instrument, perform the following steps to clean or

decontaminate the sequencer.

Note:

Dispose of all waste in appropriate liquid or solid waste containers.

Remove each Genexus

™

Bottle 2, then remove and empty the Genexus

™

Bottle 1

and Waste Carboy.

Remove the Genexus

™

Cartridge.

Inspect the floor of the sequencing reagents bay and Genexus

™

Cartridge port for

liquid.

Using absorbent paper, soak up as much liquid as possible, then wash the

affected area with 10% bleach solution.

Wipe the affected surfaces with 70% isopropanol, then allow to air-dry.

Materials required

Clean or

decontaminate the

sequencer

134

Genexus

™

Integrated Sequencer User Guide

Summary of Contents for Ion Torrent A45727




































































































































































Search results

Summary of Contents for Ion Torrent A45727

Reviews:

Related manuals for Ion Torrent A45727

Brands by name

Popular brands

Thermo Scientific Ion Torrent A45727, User Manual

Search results

Summary of Contents for Ion Torrent A45727

Reviews:

Related manuals for Ion Torrent A45727

Brands by name

Popular brands