Thermo Scientific Ion Torrent A45727 User Manual Download Page 16

Page: 16 / 163

The Genexus

™

Controls kit (Cat. No. A40267) provides sufficient Genexus

™

Control

Library-AS to perform four library runs. The kit also provides sufficient Genexus

™

Control Panel-AS and Genexus

™

DNA Control to perform eight sample runs.

Component

Quantity

Storage

Genexus

™

Control Library

‑

1 tube

−30°C to −10°C

Genexus

™

Control Panel

‑

8 carriers (white)

Genexus

™

DNA Control

2 tubes

The Genexus

™

Filter (Cat. No. A40302) is installed in the liquid waste disposal port on

the instrument deck to prevent liquid waste line blockage. For information on

installation, see “Replace the Genexus

™

Filter“ on page 135.

Component

Quantity

Storage

Genexus

™

Filter

2 filters

15°C to 30°C

Oncomine

™

GX assays

Ion Torrent

™

Oncomine

™

GX assays are Genexus

™

-ready assays su

icient for

reactions,

and

are supplied in pre-measured ready-to-load Genexus

™

Primer Pool

Tubes. Assays are provided with Genexus

™

Library Strips 1 and 2-AS (Cat. No.

A40252) or Genexus

™

Library Strips 1 and 2-HD (Cat. No. A40255) in the amount

listed.

Contents

Carrier

color

Pool

Carriers/kit

Part No.

Storage

Oncomine

™

Comprehensive Assay v3 GX (Cat. No. A46296)

Oncomine

™

Comprehensive Assay v3 DNA GX

Purple

DNA Pool 1

A40281

−30°C to

−10°C

Teal

DNA Pool 2

Oncomine

™

Comprehensive Assay v3 RNA GX

Orange

RNA Pool 1

A44351

Blue

RNA Pool 2

Genexus

™

Strip 1

Red

—

2 × 8

A40254

2°C to 8°C

Genexus

™

Strip 2

‑

Blue

—

2 × 8

A40253

−30°C to

−10°C

Oncomine

™

Precision Assay GX (Cat. No. A46291)

Oncomine

™

Precision Assay GX (panel only)

Purple

OPA Pool 1

(FWD and REV

primers)

A44350

−30°C to

−10°C

Genexus

™

Strip 1

Red

—

A40254

2°C to 8°C

Genexus

™

Strip 2

‑

Purple

—

A40256

−30°C to

−10°C

Genexus

™

Controls

Genexus

™

Filter

Chapter 1

Product information

Oncomine

™

GX assays

Genexus

™

Integrated Sequencer User Guide

Summary of Contents for Ion Torrent A45727




































































































































































Search results

Summary of Contents for Ion Torrent A45727

Reviews:

Related manuals for Ion Torrent A45727

Brands by name

Popular brands

Thermo Scientific Ion Torrent A45727, User Manual

Search results

Summary of Contents for Ion Torrent A45727

Reviews:

Related manuals for Ion Torrent A45727

Brands by name

Popular brands