Theben 4940301 User Manual Download Page 36

Page: 36 / 88

ETS communication objects

Manual DALI gateway S64 KNX/S128 KNX

Sends the set Y value as status of the group.

8.5

ECG objects

8.5.1

ECG objects – behaviour

A communication object is available for each of the up to 64 connected ECGs and corresponding

lamps to display the failure status. (Example ECG 1):

Object Object name

Function

Type

Flags

519

ECG1, Switching

On/Off

1 Bit

1.001

Use this object to switch an ECG on or off if it is not in special mode (test mode, emergency

lights, panic/ emergency mode).
520

ECG1, Dimming

Brighter/Dar

ker

4 Bit

3.007

This object is used for the relative dimming of an ECG that is not in special mode (test mode,

emergency lights, panic/ emergency mode). Bit 3 is set to dim up and deleted to dim down.

Bits 0 to 2 refer to the increment size. Bit 0 to 2 deleted is interpreted as a stop telegram.
521

ECG 1, Set Value

Value

1 Byte

5.001

Sets the value of ECG1 unless it is in special mode (test mode, emergency lights, panic/

emergency mode).
522

ECG1, Enable

Yes/No

1 Bit

1.003

Note:

Object 522 is shown for the following parameter: ECG 1



General



Function of the

additional object.

Use this object to enable the operation of ECG 1:

Object = 0



Operation disabled Object = 1



Enable operation

522a ECG1, Disable

Yes/No

1 Bit

1.003

Use this object to disable the operation of ECG 1:

Object = 0



Enable operation Object = 1



Operation disabled

523

ECG1, Status

On/Off

1 Bit

1.001

CRT

Sends the ECG switch status. Each value >0% is interpreted as ON.

524

ECG 1, Status

Value

1 Byte

5.001

CRT

Sends the ECG value status.

Summary of Contents for 4940301

























































































Search results

Summary of Contents for 4940301

Reviews:

Related manuals for 4940301

Brands by name

Popular brands

Theben 4940301, User Manual

Search results

Summary of Contents for 4940301

Reviews:

Related manuals for 4940301

Brands by name

Popular brands