Theben 4940301 User Manual Download Page 32

Page: 32 / 88

ETS communication objects

Manual DALI gateway S64 KNX/S128 KNX

HSV value

The colour is set as an HSV value which consists of hue, saturation and value. The value (V) is

set via the value object 41. Further objects are displayed for the hue (H) and saturation (S).

Figure 5: HSV-colour spectrum (Source: Wikipedia

The hue is set as a value between 0° and 360° and hence rotates around the colour circle. This

means that this value is required to reach all colours in the colour circle.

Figure 6: HSV-colour value (Source: Wikipedia)

The values for saturation and intensity range from 0 to 100 %.

Complete saturation and full intensity are reached by selecting 100 %.

Obj

Object name

Function

Type

Flags

G1, Colour (HSV) Hue

Value

1 Byte

5.003

Sets the colour as an HSV value. The hue values are transferred as values between 0° and

360°. Please note that only a resolution of approx. 1.4 ° is possible with the 5.003 data type

used.

G1, Colour (Saturation)

Value

1 Byte

5.001

Sets the saturation level. The saturation values are transferred as values between 0 and 100

%.
86

G1, Colour (HSV) Fading Hue

Brighter/Cooler

4 Bit

3.007

Changes the hue within the group. Bit 3 is set to increase the angle and deleted to reduce the

angle. Bit 0 to 3 deleted is interpreted as a stop telegram. This means that the entire

circumference of the circle can be circulated, and every color can be set.
87

G1, Colour (Saturation)

Brighter/Cooler

4 Bit

3.007

See change of hue above. The value from 0 to 100% is increased in increments.

G1, Colour (HSV) Hue

Status

1 Byte

5.003

CRT

Sends the selected hue as status of the group.

G1, Colour (HSV) Saturation

Status

1 Byte

5.001

CRT

Sends the selected saturation as status of the group.

Summary of Contents for 4940301

























































































Search results

Summary of Contents for 4940301

Reviews:

Related manuals for 4940301

Brands by name

Popular brands

Theben 4940301, User Manual

Search results

Summary of Contents for 4940301

Reviews:

Related manuals for 4940301

Brands by name

Popular brands